View M54687FP_4344765.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M54687FP
Bi-Directional Motor Driver with Governor
REJ03F0048-0100Z Rev.1.0 Sep.19.2003
Description
The M54687FP is a semiconductor integrated circuit that is capable of directly controlling the rotating direction and rotating speed of a smallsize bi-directional motor rotating in both forward and reverse directions.
Features
* * * * * Capable of controlling the speed in forward and reverse rotating directions Capable of controlling the speed in high speed mode Large output current drive (IO(max) =700mA) Built-in clamp diode Flat package (16P2N)
Application
Micro-cassette for phone-answering machine, AV equipment, and other general consumption appliances
Function
The M54687FP is an IC that can control the forward rotation, reverse rotation and speed of small DC brush motor. For the basic operation of this IC, output modes are selected, as shown in the logic truth table, by entering appropriate H/L level into the R, L and S inputs. Two resistances are put between the output pin and the PSC pin and the resistance ratios are appropriately adjusted to perform the speed control. In addition to the above, speed control can be done by varying the voltage at VR pin, in the high speed mode.
Pin Configuration
Speed control 1 R input S input PSC1 R S GND L input L 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 NC O2 Output 2 P-VCC Power supply O1 VR GND Output 1 High speed control
M54687FP
Power supply L-VCC Speed control 2 PSC2
P-VCC Power supply
Outline 16P2N-A
NC: no connection
Rev.1.0, Sep.19.2003, page 1 of 8
M54687FP
Logic Truth Table
Input R H H L L H L H L L H L H L H L L H S H H H H L L L L Output O1 H H FG G L OFF O2 FG G H H L OFF Mode FF PLAY REW REV BRAKE STB Forward rotation high speed governor Forward rotation governor Reverse rotation high speed governor Reverse rotation governor Brake operation Standby mode output high imp. Reserved
G: Governor control output mode FG: Rotating speed controllable with the voltage at VR pin (However, the precision is worse than G.)
Block Diagram
Speed control 1 PSC1 1 High Speed control VR 14 Output 1 O1 15 Output 2 O2 10 Speed control 2 Power supply PSC2 VCC 8 7 9 16
Reference voltage
(-)
Activation circuit
(-)
Control circuit
2 R R input
6 L L input
3 S S input
4 5 12 13 GND
Rev.1.0, Sep.19.2003, page 2 of 8
Constant voltage, Constant current
Reference voltage
M54687FP
Absolute Maximum Ratings
(Ta = 25C unless otherwise noted.)
Parameter Power supply Input voltage Output voltage Allowable motor rush current Continuous output current Power dissipation Operating temperature Storage temperature Symbol VCC VI VO IOP IO Pd Topr Tstg Ratings -0.5 - +14 -0.5 - VCC -0.5 - VCC+2 700 200 1.14 -20 - 75 -40 - 125 Unit V V V mA mA W C C tON 100ms, duty of 1% or less. However, Pd must not exceed the maximum rating. When mounted in board Condition
Thermal Derating (Absolute Maximum Rating)
2.0
Power Dissipation Pd (W)
1.5 When mounted in board 1.0
0.5
0 0 25 50 75 100
Operating Temperature Ta (C)
Recommended Operational Conditions
(Ta = 25C unless otherwise noted.)
Limits Parameter Supply voltage "H" input voltage "L" input voltage VR control voltage range* Symbol Vcc VIH VIL VR Min. 6.0 2.0 0 0 Typ. 9.0 Max. 13.0 Vcc 0.4 Vcc Unit V V V V
* : IO 200mA when FF/REW speed is controlled.
Rev.1.0, Sep.19.2003, page 3 of 8
M54687FP
Electrical characteristics
(Ta = 25C, unless otherwise noted.)
Symbol IO(leak) II VOH VOL ICC1 ICC2 ICC3 ICC4 Vref IB K Vref / VCC Vref K / VCC K Vref / IO Vref K / IO K Vref / Ta Vref K / Ta K Vref II Vref / VCC Vref Vref / IO Vref Vref / Ta Vref IB IR Parameter Output leak current Input current "H" output voltage "L" output voltage FF/REW PLAY/REV BRAKE STAND BY Reference voltage Bias current Current proportional constant Voltage characteristics Vref K Vref K Temperature characteristics Vref K
Governor characteristics (II) FF*REW Reference voltage
Test conditions VCC = 14V, VO = 14V Standby mode VI = 5.0V IO = -200mA, VR = 5.0V IO = 200mA, VR = 0V, Vpsc = 2.5V FF / REW / BRAKE mode Output open Output open Output open
Min.
Limits Typ. 0
Max. 100 1.0 - 0.5 8.0 8.0 48 10.0 1.05 1.7 22
Unit A mA V V mA mA mA A V mA - %/V %/V %/mA %/mA %/C %/C V %/V %/mA %/C
0 0.4 VCC-1.2 VCC-0.9 - - - - - 0.95 0.7 18 0.22 5.0 5.0 35 0 1.0 1.2 20 0.1 0.2 0.02 0.01 0.01 0.01 2.0 3.0 0.2 0.1 0.7 0 1.3 -5.0
Supply current
IO = 40mA VCC = 6.0 - 13V VCC = 6.0 - 13V IO = 40mA IO = 50 - 200mA IO = 50 - 200mA Ta = -20 - 75C Ta = -20 - 75C VR = 0.3V
Governor characteristics (I) PLAY*REV mode
Current characteristics
Voltage characteristics Current characteristics Temperature characteristics
VR = 0.3V VCC = 6.0 - 13V VR = 0.3V IO = 50 - 200mA VR = 0.3V Ta = -20 - 75C VR = 0.3V VR = 0V
Bias current VR input current
1.8 -20
mA A
Rev.1.0, Sep.19.2003, page 4 of 8
M54687FP
Application Example
When the normal speed is set to 2000rpm, and the high speed is set to 3500rpm
2k RS 0.1F
VCC = 9.0V RT 300
VCC = 5.0V PSC1 20k
RT M O1
/ / 5.6 k
10F O2 PSC2 VCC
VR
1k
Reference voltage
(-)
Activation circuit
(-)
Control circuit
P-G
R
L Control signal
S
Install at a position close to the IC, if possible.
Motor: Armature resistance Ra = 14 RT: The resistance of 300
, Generation constant Ka = 2.57 3000 is used for temperature compensation to take measures against hunting at low temperature.
Rev.1.0, Sep.19.2003, page 5 of 8
Constant voltage, Constant current
L-G
Reference voltage
M54687FP
Speed Control Method
(1) Speed Control Method I (See the application circuit drawing.) For PLAY/REV Rotation number can be expressed by the following formula:
N= 1 {IB * RT+Vref (1+ RT )+la( RT -Ra)} * * * * * * (1) Ka RT+RS K
Where: Motor generation constant: Ka, Motor armature resistance: Ra, Rotation number: N K: Current proportional constant, IB: PSC pin bias current, Ia:motor current RT, RS: External resistance In addition, to set the rotation number with RS, external resistance RT is generally set as follows: RT K x Ra For FF/REW Note that the rotation number is basically controlled with the same expression as formula (1) but different reference voltage Vref and different bias current IB are to be used. However, Vref 5VR+0.5 (2) Speed Control Method II (to increase the motor rotation number)
RS
RT M
RT
PSC1
O1
O2
PSC2
VR
VCC
R
L
S
L-G
P-G
Control signal
In the external circuit above, the voltage across motors is almost determined by the ratio of `RS+RT' to `RT' and, therefore, a value set for the voltage across motors is not so large. As method (1) of speed control I, the rotation number can be controlled. However, the following relations must be satisfied: RTRT+RS RS+RTRT
Rev.1.0, Sep.19.2003, page 6 of 8
M54687FP (3) Speed Control Method III (to increase the precision of forward rotation and reverse rotation)
RS1 RT1
RT2
RS2
M
PSC1
O1
O2
PSC2
VR
VCC
R
L
S
L-G
P-G
Control signal
The above two applications cannot make fine adjustments in forward rotation and reverse rotation (because the external resistance is shared with the forward rotation and reverse rotation). Fine adjustments can be made for each of forward rotation and reverse rotation if the external circuit is set as shown in the drawing above. This external circuit is also available to change the speed of forward and reverse rotation. The control method adopts the same formula as formula (1). However, the following relations must be satisfied: RT+RSRS1 or RS2 RTRT1 or RT2
CAUTIONS
(1) Oscillation may take place with the setting of RT>K*Ra. Set R K*Ra. (2) Add a capacitor of 0.1F to the portion between PSCs to reduce brush noise of the motor. (3) Add a capacitor of 10F to the portion between VCC and GND to reduce brush noise and back electromotive noise of the motor. (4) At a low temperature, RT>K*Ra is set due to temperature characteristics of resistance Ra of the motor. When oscillation takes place, use resistance with a temperature coefficient for RT. (5) When the supply voltage is low, note that saturation of the output transistor of the IC may prevent the rotating speed for control. Taking into account motor noise etc., set constants in the following range.
2.0V VCC - (EC+Ia * Ra) RT = VCC - {RT * IB + Vref(1+ RT )+ K RS
*
Ia}
When the back electromotive force is large with the brakes applied, for example, malfunction may occur in internal parasitic Di. If flyback current of 1A or more flows, add Schottky Di to the portion between the output and the GND. When the IC is used at a high speed for PWM etc., note that switching of output results in delay of approx. 10s.
Rev.1.0, Sep.19.2003, page 7 of 8
M54687FP
16P2N-A
JEDEC Code -- e b2 Weight(g) 0.2 Lead Material Cu Alloy
MMP
Plastic 16pin 300mil SOP
EIAJ Package Code SOP16-P-300-1.27
Package Dimensions
16
9
HE
E
L1
L
Rev.1.0, Sep.19.2003, page 8 of 8
e1
Recommended Mount Pad Symbol
1 8
F A
G
D
A2
b
A1
x
M
e y
A A1 A2 b c D E e HE L L1 z Z1 x y c
z Detail G Detail F
Z1
b2 e1 I2
Dimension in Millimeters Min Nom Max 2.1 0 0.1 0.2 -- 1.8 -- 0.35 0.4 0.5 0.18 0.2 0.25 10.0 10.1 10.2 5.2 5.3 5.4 -- 1.27 -- 7.5 7.8 8.1 0.4 0.6 0.8 -- 1.25 -- -- 0.605 -- -- 0.755 -- 0.25 -- -- -- -- 0.1 0 -- 8 -- 0.76 -- -- 7.62 -- -- 1.27 --
I2
Sales Strategic Planning Div.
Keep safety first in your circuit designs!
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
RENESAS SALES OFFICES
Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001
http://www.renesas.com
(c) 2003. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon 1.0

▲Up To Search▲

Price & Availability of M54687FP

	To Download M54687FP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .